0.66kV Solid Core Current Transformer Selection Guide for Low-Voltage Switchgear
To select a 0.66kV solid core current transformer (CT) for low-voltage switchgear, first confirm the system voltage and primary current, then match the CT’s ratio, accuracy class, burden, insulation requirements, and physical dimensions to the application. A solid core CT has a closed magnetic core, so the conductor generally needs to be disconnected before the CT can be fitted. It is commonly considered for fixed installations where the switchgear layout and installation sequence allow this. At SINAVA, we recommend confirming the complete specification against the switchgear design and the intended metering or protection function before requesting a quotation.
If you want to learn more, please visit our website.
Key Takeaways
- “0.66kV” identifies a voltage rating; it does not define the CT’s current ratio or accuracy.
- Choose the ratio and accuracy for the connected meter, relay, or monitoring device, not by primary current alone.
- Check the core opening, mounting arrangement, busbar or cable dimensions, and installation access before ordering.
- Share the application details and technical documents with your supplier to clarify configuration, testing, and delivery requirements.
Who This Guide Is For
This guide is intended for switchgear engineers, electrical contractors, panel builders, procurement teams, and distributors evaluating CTs for low-voltage equipment. It is useful when preparing a new panel design, replacing a CT, or comparing supplier quotations. The appropriate specification depends on the system, connected instruments, and applicable project requirements, so this guide should support—not replace—engineering review.
What a 0.66kV Solid Core Current Transformer Does
Basic operating concept
A CT reproduces a reduced secondary current that corresponds to current flowing through its primary conductor. A meter, monitoring device, or protection relay can use that secondary signal, provided the CT ratio and performance characteristics are compatible with the connected equipment. A solid core CT surrounds the primary conductor with a closed magnetic circuit, rather than opening into a hinged or split form.
The 0.66kV designation relates to the CT’s voltage rating as specified by the manufacturer; it is not a current ratio. A ratio such as 100/5A describes a primary current of 100A corresponding to a secondary current of 5A under the specified operating conditions. Treat these values as separate selection fields and verify the exact meanings and ratings on the product documentation.
Typical functions and applications
Solid core CTs may be used for current measurement, energy metering, monitoring, or protection, depending on their design and specified accuracy or protection performance. Potential applications include low-voltage distribution boards, motor control centers, and fixed switchgear assemblies. The final suitability depends on the electrical design, environmental conditions, instrument requirements, and installation arrangement.
Types, Materials, and Specification Overview
CTs can differ in core design, winding arrangement, enclosure, terminal configuration, and mounting method. Core materials and construction affect magnetic performance, but the buyer should assess these through the manufacturer’s stated electrical specifications and supporting documents rather than assume performance from a material name alone. For a solid core model, confirm that the aperture and mounting geometry suit the actual conductor or busbar.
| Specification | What to confirm | Why it matters |
|---|---|---|
| Rated voltage | Compatibility with the system and equipment design | Confirms the CT is intended for the specified voltage environment. |
| Current ratio | Primary and secondary current, for example 100/5A | Must match the expected current range and connected device input. |
| Accuracy or protection class | Required class and intended duty | Measurement and protection applications may require different performance. |
| Rated burden | Permitted connected load, stated in VA | Helps check the CT against instruments, relays, and secondary wiring. |
| Mechanical dimensions | Opening, overall size, fixing points, and terminal access | Supports safe fit and maintainable installation in the panel. |
How to Match a CT to the Application
1. Confirm system and conductor details
Record the system voltage, expected operating current, conductor type, and available space. Identify whether the primary passes through the CT once or uses another arrangement specified by the design, as this affects the effective ratio. If the CT is for replacement, compare the existing nameplate and drawings, but do not assume that a visually similar unit is electrically interchangeable.
2. Define the connected device and purpose
State whether the CT feeds a meter, energy meter, monitoring device, or protection relay. Confirm the secondary input expected by that equipment, such as 1A or 5A, and obtain the required accuracy or protection class from its documentation or the project specification. The correct selection is application-specific; a ratio alone is not enough to determine suitability.
3. Check burden and secondary circuit
Review the connected device burden and account for the secondary wiring in the circuit assessment. Compare the resulting requirement with the CT’s declared rated burden and the applicable design limits. Have a qualified engineer verify the calculation where the application depends on measurement accuracy or protection performance.
With competitive price and timely delivery, SINAVA sincerely hope to be your supplier and partner.
4. Verify installation and safety requirements
Measure the conductor or busbar and check the CT aperture, overall dimensions, fixing method, clearances, and terminal direction. Because the core is closed, installation normally requires access to the conductor before connection or during a planned shutdown. Follow site procedures and applicable electrical safety rules; a CT secondary should not be left open-circuit while primary current is flowing.
Selection Factors That Often Need Clarification
Frequency is one example: a system may operate at 50Hz or 60Hz, so state the project frequency and confirm the CT is suitable for it. Environmental conditions also matter; provide the expected indoor or outdoor location, ambient conditions, and any enclosure or ingress-protection requirements specified by the project. Do not infer these characteristics from the 0.66kV rating.
Polarity markings, terminal arrangement, and conductor orientation should be clear in the drawing or order specification, particularly where multiple CTs are installed together. Confirm how the CT will connect to the secondary circuit and whether shorting or test facilities are required by the panel design. Project standards and documentation requirements should also be listed explicitly rather than assumed to be included.
Pricing, MOQ, and Lead-Time Considerations
Pricing can depend on the ratio, accuracy or protection requirements, burden, dimensions, terminal configuration, and order quantity. Custom dimensions or documentation requests may also affect quotation and production planning, but the impact must be confirmed for the specific order. Minimum order quantities and lead times vary by supplier, configuration, and availability, so request written confirmation rather than relying on a general estimate.
For a comparable quotation, send the same technical information to each supplier. Include drawings or photographs with dimensions where appropriate, the required quantity, delivery destination, target schedule, and inspection or documentation needs. This gives suppliers a clearer basis to identify any technical exceptions before commercial terms are finalized.
Supplier Evaluation Checklist
- Can the supplier confirm the requested voltage rating, ratio, burden, and accuracy or protection class in writing?
- Will the supplier review dimensions, aperture, mounting, and terminal details against the panel drawing?
- What product documentation and routine inspection information can be provided for the offered configuration?
- Are quotation validity, MOQ, production lead time, packaging, and shipping terms clearly stated?
- How will engineering questions, specification changes, and nonconformities be handled?
As a manufacturer and supplier, SINAVA can review an inquiry based on the buyer’s stated electrical and mechanical requirements and clarify the information needed for product evaluation. Please provide the relevant nameplate details, drawings, or specification sheet where available. Any offered configuration should be checked against the final project requirements before purchase and installation.
Conclusion: What to Do Before You Order
A 0.66kV solid core CT can be a suitable option for fixed low-voltage switchgear when its voltage rating, current ratio, accuracy or protection performance, burden, and physical fit meet the application requirements. The most important next step is to compile those requirements and verify them with the connected device and switchgear design. Remember that a closed core usually needs conductor access for installation, so include installation planning early.
For your next step, prepare the system voltage and frequency, primary and secondary current, intended function, burden or connected-device details, dimensions, quantity, and required delivery schedule. Send this information to SINAVA for a configuration review and quotation. Confirm the final technical documents and safety arrangements with your project engineer before procurement and commissioning.



